Home

Blog

Blog

  • How to replace a flush valve on a kohler toilet ?
    Apr 24, 2025
      Kohler toilets are known for their design and reliable performance, but like all plumbing components, some parts eventually wear out. One of the most common issues is a faulty flush valve. Whether you're dealing with a leak, a weak flush, or a constantly running toilet, replacing the flush valve can restore proper function. This guide will walk you through how to replace a flush valve on a Kohler toilet — whether it's the entire valve or just the inner canister — with tips on choosing the right parts based on your model and the types of toilet flushing systems.   1. Introduction   The flush valve controls how water exits the tank and enters the bowl. Over time, the valve may wear out, leading to water waste or inefficient flushing. This post focuses on Kohler toilet flush valves, particularly the 2-piece models, and will help you assess the issue, select the right part, and install it step by step.   2. Preparation Before Replacement   A. Diagnose the Issue   Before buying a new part, determine whether the entire flush valve is damaged or only the canister (also called the float or tower) needs replacement. If the tank structure is fine and only the center bucket is worn or cracked, you can save time and money by buying a flush valve repair kit.   B. Identify the Right Model   Kohler offers a wide range of valves, including the 4 inch toilet flush valve used in many of their modern models. Each flush valve dimension is typically matched to specific toilet models. Using the wrong size or type may lead to leaks or incompatibility. Always check the model number stamped inside the tank or refer to your toilet manual for an exact match. This is especially important for Kohler two piece toilet flush valve replacement tasks.   C. Tools You'll Need   Adjustable wrench, Screwdriver, Towel or sponge, Replacement flush valve or canister, Rubber gloves (optional)   D. Safety First   Turn off the water supply   Flush the toilet to empty the tank   Disconnect the refill tube and chain from the flush lever   3. Installation Guide   Depending on your diagnosis, choose one of the following methods:   A. Full Flush Valve Replacement   When to choose: Cracked base, constant leaks, or worn-out sealing surfaces.   Removal Steps:   Remove the tank lid and place it aside   Disconnect the refill tube   Unhook the chain from the flush lever   Use an adjustable wrench to loosen the large plastic nut underneath the tank   Lift the entire flush valve out and clean the tank bottom   Installation Steps:   Insert the new flush valve into the tank hole   Tighten the mounting nut from below   Reattach the refill tube and flush chain   Ensure everything is secure and aligned   B. Replacing Only the Canister (Bucket)   When to choose: The tank and base are fine, but the canister is leaking, warped, or sluggish.   Removal Steps:   Remove the tank lid   Disconnect the refill tube and flush chain   Grip the canister’s crossbar and rotate counterclockwise to unlock it from the base   Installation Steps:   Align the new canister’s notches with the base slots   Rotate clockwise to lock in place   Reattach the chain and refill tube   This is one of the easiest forms of flush valve repair kit usage and avoids tank removal entirely.   4. Testing and Adjustment   Turn the water supply back on   Let the tank fill and observe any leaks around the base   Perform several flushes to ensure smooth operation   Adjust chain length if the flush is too weak or the flapper doesn’t seal properly   5. Conclusion   Replacing a flush valve may sound technical, but with the right tools and guidance, it’s a straightforward task. Whether you're dealing with a Kohler two piece toilet flush valve replacement or simply swapping the flush valve repair kit components, proper installation ensures water efficiency and a reliable flush every time.   Always confirm your flush valve dimension and type before buying, as Kohler models vary widely among different types of toilet flushing systems.
    Read More
  • How to change a toilet flush button ?
    Apr 16, 2025
      When your push button toilet starts acting up—whether the button sticks, doesn't rebound, or causes continuous flushing—it might be time for a buttons replacement. Replacing a toilet flush button may sound like a hassle, but it's actually a simple process that most people can do themselves with minimal tools.   Why Replace a Toilet Flush Button?   Over time, flush buttons can wear out or become less responsive. This can lead to poor flushing performance, water waste, or even a broken flush valve button. Replacing the button can restore proper flushing and give your dual flush toilet tank a longer life.   Preparation Before Replacement   You only need a few tools like a wrench and a cloth. Before you begin, identify how the button is fixed in place. There are three common types: Buttons fixed on the push button flush valve Buttons mounted on the toilet tank lid Buttons mounted on the wall or front panel (common in concealed tanks) You’ll also need to purchase a replacement that matches your existing setup. Make sure to check if it’s a single or two button toilet design, and ensure the button diameter fits your existing opening.   Replacement Steps by Button Type   1. Buttons Fixed on the Flush Valve   These are the simplest to replace. No need to open the tank lid. Just twist the old button to unscrew it from the valve. Insert the new button into the hole and tighten it by turning. This type not only simplifies installation but also helps hold the lid in place securely.   2. Buttons Mounted on the Tank Lid   First, remove the lid. If it’s a cable-operated system, press the release clips on the control box to detach it from the button. Unscrew the nut securing the button to the lid and remove the old unit. Insert the new button through the hole, reconnect the rod or cable, and tighten the nut. If the rod is too long and interferes with flushing, trim it with a utility knife. Replace the lid and test the button for smooth operation.   3. Buttons Mounted on the Wall or Tank Panel   These are typically found on concealed or in-wall dual flush toilet tank systems. Start by removing the faceplate or cover. Detach the control box or rods from the old button. Unscrew the mounting nut and remove the button module. Insert the new button into the hole, secure it with the nut, and reconnect the control mechanism. Reattach the faceplate and press both buttons to test flush performance.   Common Issues & Troubleshooting   Loose buttons after installation: Ensure the nut is tightened securely and that any gaskets are in place. One of the flush options not working: Adjust the cable or rod length to ensure proper engagement with the flush valve. Not sure what button to buy? Choose universal models that match your push button toilet setup in terms of diameter and function.   Conclusion: You Can Do It!   Changing your toilet’s flush valve button is one of the easiest home maintenance tasks. With just a few steps and a proper replacement, your push button toilet will be working like new again. Whether you have a two button toilet or a single-button setup, Jielin offers a range of high-quality buttons for easy replacement.   Need help choosing the right model? Visit our product page to explore our full catalog, complete with specs, images, and installation videos.
    Read More
  • How often to replace toilet flapper ?
    Apr 08, 2025
      Have you ever noticed your toilet making constant dripping sounds? Or maybe your flush isn’t as strong as it used to be? Or worse—your water bill suddenly went up for no reason? Well, don’t panic—it might not be a serious plumbing issue. In many cases, it’s just your toilet flapper acting up!   This small rubber part plays a big role in your toilet’s flushing system. So let’s answer the question: how often should you replace your toilet flapper?   What Is a Toilet Flapper?   In simple terms, the toilet flapper is a rubber seal inside the tank that controls the flow of water into the toilet bowl. When you press the flush button or handle, the flapper lifts up, allowing water to rush into the bowl. Once the tank is empty, it drops back down to seal the tank so it can refill.   Over time, the flapper can get worn out, warped, or cracked—causing leaks or weak flushes.   How Long Does a Toilet Flapper Last?   In most homes, a flapper lasts around 3 to 5 years. Not bad, right? But this depends on a few things:   Water quality – Hard water or water with chlorine can wear out PVC faster   Usage – The more often your toilet is used, the faster the flapper wears down   Material – Rubber flappers tend to last longer than PVC ones   So even if it’s still “working,” it’s a good idea to check it regularly and replace it if needed.   Signs You Need to Replace Your Toilet Flapper   Not sure if your flapper needs replacing? Here are some clear signs to watch out for:   Your toilet keeps running – That constant water sound means the flapper isn’t sealing properly.   Weak or incomplete flushes – If flushing isn’t doing the job, the flapper may not be opening fully.   Water leaking into the bowl – Look closely: if water keeps trickling even when the toilet hasn’t been flushed, it’s probably the flapper.   Visible wear and tear – Take off the tank lid and look at the flapper. If it looks cracked, warped, or sticky, it’s time for a new one.   A faulty flapper can waste hundreds of gallons of water per month—so it’s not just a small problem!   How Often to Replace Toilet Flapper?   So, back to the main question: how often should you replace your toilet flapper?   The general rule is every 3 to 5 years. But that’s just a guideline. Here’s when you should consider replacing it more frequently:   If you live in an area with hard water or chlorinated water   If your toilet is used heavily, like in a large household or a public restroom   If you notice any of the signs mentioned above   Including flapper checks in your regular toilet maintenance routine is a smart move. It’s a small part, but it can prevent big headaches—and high water bills.   Conclusion   Your toilet flapper may be small, but it plays a huge role in keeping your bathroom running smoothly and your water bills under control. By replacing it every few years—or sooner if needed—you can avoid leaks, save water, and keep your flush strong and reliable.
    Read More
  • How to replace toilet fill valve?
    Apr 01, 2025
    The toilet is one of the most frequently used fixtures in any household, and the toilet fill valve is a key component that controls the water refilling process inside the tank. When problems such as slow filling or constant running occur, a faulty toilet fill valve is often the cause.   While it might seem like a job for a plumber, replacing a toilet fill valve is a fairly simple DIY task. It can save you time and money, and also gives you a better understanding of your home’s plumbing system.   In this guide, we'll walk you through the complete process of removing the old toilet fill valve, installing a new one, and adjusting water levels—so you can easily handle this home maintenance task yourself.    Tools and Materials Needed   Before you begin, gather the following tools and materials to ensure a smooth installation:   a. Adjustable wrench or pliers – For loosening and tightening the locknut underneath the tank.   b.Bucket or towel – To catch any residual water that may leak during disassembly.   c. New toilet fill valve – Choose a compatible model, preferably a universal type with adjustable height. Make sure the universal toilet fill valve inlet matches your supply hose connector:  Europe & Africa: G3/8" Middle East: G3/8" or G1/2" Asia & South America: G1/2" Peru: G7/8" or 15/16-14NPSM North America: 15/16-14NPSM   Preparation   To avoid spills and ensure safety, follow these steps before removing the old valve:   Step 1: Turn off the water supply Locate the shut-off valve near the toilet and turn it clockwise until it stops.   Step 2: Flush to empty the tank Hold down the flush lever or button to drain as much water as possible from the tank.   Step 3: Place a bucket or towel under the tank inlet This will catch any remaining water when you disconnect the supply hose.   Step 4: Disconnect the water supply hose Use your hand or a wrench to loosen the hose from the base of the fill valve.   Removing the Old Toilet Fill Valve   Now you're ready to remove the existing valve:   Step 1: Loosen the locknut under the tank Use a wrench to turn the plastic locknut counterclockwise. Note: Some two-piece toilets have tight spaces that make it hard to reach the locknut. In such cases, you may need to detach the tank from the bowl for easier access.   Step 2: Pull out the old toilet fill valve Lift the valve out from inside the tank. If it’s stuck, gently wiggle it back and forth to loosen it.   Step 3: Inspect and clean the inlet hole Check for debris, hard water buildup, or damage. Clean the area with a cloth and inspect the rubber gasket—replace it if worn.    Installing the New Fill Valve   Step 1: Adjust the new valve’s height based on the old one Compare the old and new toilet fill valves, and adjust the body and float of the new valve to match the original height. Ensure the float doesn’t interfere with other tank components.   Step 2: Insert the valve into the tank Slide the valve into the inlet hole with the rubber washer seated snugly inside the tank.   Step 3: Tighten the locknut from below Secure the valve by tightening the locknut underneath the tank. Hand-tighten first, then use a wrench with light pressure.   Step 4: Reconnect the water supply hose Attach the hose to the bottom of the new fill valve. Ensure a snug and leak-free fit.   Step 5: Connect the refill tube to the overflow pipe Insert the refill tube into the flush valve’s overflow pipe and clip it in place. This small tube directs water into the bowl during refilling to maintain the water seal.   Testing and Adjustments   Step 1: Turn the water supply back on Slowly reopen the shut-off valve and let the tank fill.   Step 2: Check for leaks Inspect the base of the tank and the hose connection. If there are any drips, retighten the fittings.   Step 3: Adjust the water level Use the height adjustment screw or float slider to fine-tune the fill level. The water should sit 1–2 cm below the top of the overflow tube.   Step 4: Test the flush Flush the toilet 2–3 times to make sure everything works correctly and there are no slow fills or continuous running.   Tips and Common Issues   Common Issues Tips How do I know the fill valve height is correct? The water level should sit just below the overflow pipe—typically 1–2 cm lower. What if water fills too slowly? Make sure the shut-off valve is fully open. Check if the hose is kinked or clogged. Remove and clean the valve’s filter screen. Why doesn’t the water stop filling? The float may be stuck or set too high. The internal seal might be worn out. Try readjusting the float or replacing the valve’s internal components.     Replacing a toilet fill valve may seem technical, but with the right tools and a bit of patience, it’s a simple DIY task that anyone can accomplish. You’ve now learned how to identify issues, remove the old valve, install a new one, and make adjustments to ensure a perfect flush.   If you're looking for a reliable universal fill valve, consider one with adjustable height, a built-in filter, and quiet fill technology for a better experience.   Still have questions? Visit our Product page and select the Toilet Fill Valve category. Each product includes an installation video—simply choose the model that most closely matches your setup and follow along.   Take control of your home maintenance—one flush at a time!
    Read More
  • What is a Dual Flush Toilet ?
    Mar 13, 2025
    1. Introduction   In modern homes and commercial spaces, dual flush toilets have become a mainstream choice for water conservation and environmental protection. Unlike traditional single-flush toilets, dual flush toilets offer two flushing modes—half flush and full flush—allowing users to select the appropriate water volume based on actual needs, effectively reducing water waste. The design of dual flush toilets not only aligns with sustainability trends but also helps lower long-term water costs while providing more efficient flushing performance. Whether in homes, hotels, or public restrooms, dual flush toilets are widely favored for their water-saving, efficient, and durable features. In this article, we will explore the water fittings of dual flush toilets and provide a detailed introduction to their key components, helping you better understand and choose the right products.   2. Water Fittings of a Dual Flush Toilet   The efficient operation of a dual flush toilet depends on the coordination of several core water fittings, each playing a crucial role in controlling water flow, optimizing flushing performance, and conserving water. In general, the primary water fittings in a dual flush toilet include the toilet fill valve, toilet flush valve, and toilet flush button. Among these, the toilet flush valve and toilet flush button are key to the dual flush system, determining how the half and full flush functions are executed. Toilet Flush Valve: This component is responsible for releasing water from the tank to flush the bowl. Dual flush toilets typically use either a bucket-type dual flush valve or a cable-operated dual flush valve, ensuring precise water flow control and effective flushing. Toilet Fill Valve: This component controls the refilling of the toilet tank after flushing, maintaining a stable water level to ensure proper operation. Toilet Flush Button: The user operates the button to choose between a half or full flush. Depending on the installation type, toilet flush buttons can be top-mounted, side-mounted, or wall-mounted (for concealed cisterns). A well-configured set of water fittings not only impacts flushing performance but also determines the toilet's lifespan and maintenance costs. In the following sections, we will provide a detailed overview of toilet flush valves and toilet flush buttons, helping you understand their functions and key selection criteria.   3. Introduction to Key Components   3.1 Toilet Flush Valve Function: The toilet flush valve is the core component of the toilet’s flushing system, controlling water release for both half and full flushes. Common Types: Bucket-type dual flush valve and cable-operated dual flush valve. These two designs differ in installation and operation but both effectively manage water volume and optimize flushing performance. Selection Criteria: Size: Choose between a 2-inch or 3-inch toilet flush valve based on the toilet’s flush outlet size to ensure compatibility. Overflow Pipe Height: Ensure it matches the toilet tank height to prevent overflow issues. Overall Toilet Flush Valve Height: Should fit within the tank space for stable installation and effective flushing performance. Selecting the right toilet flush valve can enhance the toilet’s flushing performance while reducing water consumption and maintenance costs. When installing or replacing a toilet flush valve, always ensure it matches the toilet’s specifications for the best results. 3.2 Toilet Flush Button Function: The toilet flush button is a critical user interface component that operates the toilet flush valve, allowing selection between half and full flush modes. Common Types: Based on installation type, toilet flush buttons can be top-mounted, side-mounted, or wall-mounted, suitable for different toilet designs. Selection Criteria: Button Size: Common sizes include 38mm, 48mm, and 58mm. The correct size should match the tank hole diameter for proper installation. Installation Type: Determine whether a top-mounted or side-mounted toilet flush button is required, depending on the toilet design. Wall-Mounted Button Compatibility: For concealed cisterns, ensure the flush plate is compatible with the concealed tank, preventing installation and operational issues. Choosing the right toilet flush button affects user experience and ensures precise flushing control. When selecting a toilet flush button, consider the toilet tank structure and personal preferences to achieve optimal convenience and performance.   4. Conclusion   Understanding the water fittings and key components of dual flush toilets reveals that selecting the right toilet flush valve and toilet flush button requires considering multiple factors, such as flush outlet size, overflow pipe height, installation type, and button size. These factors determine compatibility and performance, making the selection process complex for different markets. For buyers uncertain about local toilet specifications or dealing with a variety of toilet types in their market, the most hassle-free solution is to choose a cable-operated dual flush valve with an adjustable overflow pipe. This type of toilet flush valve allows height adjustment to fit different tank designs, reducing installation issues. In this case, buyers only need to focus on the toilet flush valve size (2-inch or 3-inch) and toilet flush button size (38mm, 48mm, or 58mm), simplifying the selection process while ensuring a high success rate in compatibility. Selecting the right water fittings not only enhances toilet performance and durability but also minimizes the risk of installation errors and additional costs. Jielin Plumbing offers a wide range of high-quality dual flush toilet accessories, catering to different market needs and helping buyers easily find the most suitable products.
    Read More
  • How to remove sink overflow ring ?
    Mar 13, 2025
      1. Identify the Fastening Mechanism Most overflow rings are secured by screws or a clamping mechanism. For modern designs, look for a small screw (often hidden) that clamps the ring to the sink body. If the ring is plastic, it might be held in place by a threaded plastic nut underneath the sink.   2. Remove the Drain Assembly (If Necessary) Disconnect the drainpipe beneath the sink to access the overflow components. Use a wrench or pliers to loosen the locking nut connecting the drain to the sink. This step may require removing the entire drain assembly to reach the overflow ring.   3. Loosen the Overflow Ring For screw-fastened rings: Locate the screw (often on the underside of the sink) and use a screwdriver to remove it. If the screw is corroded, apply penetrating oil (e.g., WD-40) to loosen it. For threaded rings: Use a pipe wrench or adjustable pliers to grip the ring and turn it counterclockwise. If it’s stuck, tap gently with a rubber mallet to break the seal.   4. Address Sealant or Adhesive If the ring is sealed with plumber’s putty or silicone, carefully scrape away the residue with a utility knife or putty knife to avoid damaging the sink surface.  5. Check for Hidden Clips or Gaskets Some overflow rings have a rubber gasket or spring clip securing them. Remove the clip or pry out the gasket with a flathead screwdriver.  6. Clean and Inspect Once removed, clean the overflow hole and inspect the ring for damage. Replace any worn-out seals or gaskets to prevent future leaks.  
    Read More
  • How to remove a concealed cistern panel ?
    Mar 13, 2025
      To remove a concealed cistern panel (commonly part of an in-wall toilet system), follow these steps based on repair guides and installation manuals from multiple sources:   Step 1: Identify the Panel Type Concealed cistern panels vary by design: Push-button panels: The flush button often doubles as a removable cover. Some models require twisting or prying the button out. Flat panels: Look for hidden screws, clips, or adhesive seals around the edges.   Step 2: Prepare for Safe Removal Turn off the water supply: Locate the shut-off valve near the cistern or main water line to prevent leaks. Empty the cistern: Flush the toilet to drain water. Use a sponge or towel to remove residual water if needed.   Step 3: Remove the Flush Button or Cover For push-button systems: Press and hold the button, then twist counterclockwise or pry it out with a flathead screwdriver (insert into side grooves). Some models require lifting the button upward while gently pulling. For screw-fixed panels: Remove decorative caps (if present) to expose screws, then unscrew them.   Step 4: Detach the Panel Unclip or unscrew: Clip-fastened panels: Insert a plastic pry tool or flathead screwdriver into the gap between the panel and wall. Gently lever outward to release clips. Adhesive-sealed panels: Slice through silicone or caulk with a utility knife to avoid damaging the wall. Lift carefully: Once clips/screws are removed, tilt the panel slightly and lift it away from the wall. Avoid forcing it, as internal components (e.g., flush valve, fill valve) may still be connected.   Step 5: Access Internal Components After removing the panel: Inspect and repair parts like the flush valve, fill valve, or water supply lines. Reassemble by reversing the steps, ensuring clips/screws are securely fastened and seals are intact.  
    Read More
  • How to install toilet tank lever ?
    Mar 13, 2025
    1. Introduction   A toilet tank lever is a crucial component of the flushing system, responsible for lifting the flush valve and allowing water to flow from the tank into the bowl. Over time, it may need replacement due to wear and tear or aesthetic upgrades.   Why Replace a Toilet Tank Lever?   There are two main reasons why you might need to replace your toilet tank lever: Plastic Component Breakage – The internal plastic parts of the flush lever can break due to prolonged stress, making it impossible to flush properly. Bathroom Style Upgrade – When remodeling a bathroom or updating fixtures, you may need a new lever that matches the overall style, such as switching to black, chrome, or brushed nickel finishes.   2. Tools and Materials Needed   Before starting, gather the necessary tools and replacement parts: New Toilet Tank Lever – Before purchasing, ensure you check: Installation Type – Front-mount or side-mount lever. Handle Material – Plastic or zinc alloy. Rod Material – Plastic, aluminum, or brass. Adjustable Wrench or Pliers – Some toilet levers have nuts that may become difficult to remove due to prolonged use. In such cases, a wrench or pliers can help loosen the nut effectively.   3. Step-by-Step Installation Guide   Step 1: Turn Off the Water Supply Locate the water supply valve near the base of the toilet and turn it off to prevent accidental flushing during the installation. Step 2: Remove the Toilet Tank Lid Carefully lift the tank lid and set it aside in a safe place to prevent it from cracking or breaking. Step 3: Disconnect the Old Lever Unhook the flush chain from the lever arm. Use your hand or an adjustable wrench to loosen the mounting nut. Be aware that some levers have reverse-threaded nuts (turn clockwise to loosen). If the nut is stuck due to mineral buildup, use pliers or a wrench for extra leverage. Once the nut is loose, remove the old lever and clean any debris from the hole. Step 4: Install the New Lever Insert the new lever through the tank hole, ensuring the handle is positioned correctly for comfortable use. Secure it by tightening the mounting nut (counterclockwise if it has reverse threading). Be careful not to overtighten, as it may crack plastic parts. Step 5: Reconnect the Flush Chain To ensure proper flush function, follow these steps when adjusting the chain length: Let the chain hang naturally without lifting the flush valve cover. Align the chain with the natural resting position of the flush lever rod hole. Mark the ideal chain position and move the hook to that spot. Attach the hook securely into the lever rod hole. This method ensures that the flush valve can fully open and close without resistance. Step 6: Test the Installation Turn the water supply back on. Flush the toilet multiple times to check if the new lever operates smoothly. If the flush isn’t working correctly, adjust the chain length again to ensure the flush valve opens fully.   4. Common Installation Issues and Fixes     Issue Possible Cause Solution The lever is stuck or hard to press The nut is too tight, or the lever angle is incorrect Slightly loosen the nut and adjust the angle The flush chain is too loose or too tight Incorrect chain length Adjust the hook position to match the lever’s resting state Water keeps running after flushing The flush valve is not closing properly Check the lever and flush chain positioning; readjust if necessary The new lever doesn’t match the bathroom style Wrong finish or material Choose a lever that complements the bathroom decor, such as black, chrome, or brushed nickel     Replacing a toilet tank lever is a simple DIY task that takes just a few minutes. By choosing the right lever style and following the correct installation steps, you can: Ensure proper flushing functionality Enhance the aesthetic appeal of your bathroom Prevent future flushing issues with correct chain adjustment For long-term performance, regularly check and maintain the flush handle and chain. If any parts become worn or broken, replace them promptly to keep your toilet in top condition.
    Read More

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Our hours

24 hours online

Contact Us: jack@jlplumbing.com

home

products

WhatsApp

Contact Us